Numerical Investigation of the Capture of Polydisperse Particles by Charged Droplets

The capture of particles by charged droplets was simulated by considering the electrostatic interactions of droplet-droplet and droplet-particle. The results indicate that the electrostatic repulsion between droplets leads to a dynamic accumulation mode of particles. However, the droplet spacing has an insignificant effect on the capture efficiency when the electrostatic deposition predominates. The increase of droplet charge remarkably improves the capture efficiency, in which the capture of fine particles accounts for the largest proportion. Compared to the droplet charge, the droplet size shows a limited improvement in the capture efficiency. Reducing the droplet velocity prolongs the capture time instead of enhancing the capture capacity per unit time, thereby improving capture efficiency.     

Enhanced photoreactivity of MOFs by intercalating interlayer bands via simultaneous ?NCO and ?SCu modification

Herein, we propose a novel method to enhance the photoreactivity of an MOF catalyst by grafting isocyanate bonds ( NCO) and sulfhydryl-complexed copper ( SCu) onto ZIF-8 (NIF-SCu). The grafting process intercalated interlayer bands between the conduction and valence bands of ZIF-8, thereby providing a “ladder” for facile electron transition. The extreme improvement in the photoreactivity of NIF-SCu could be attributed to the enhancement in light responses in the range of 350–450 nm by  NCO groups and the widening of the visible light range of the MOF by  SCu groups. The formation of staggered energy levels in NIF-SCu could also narrow the band gap, lower the resistance, and facilitate the transfer of photogenerated carriers, thereby generating electrons with strong reduction potential in the  SCu conduction band. This study provides a new strategy for improving or even endowing the photoactivity of environmental functional materials with wide bandgaps.     

First Principle and Experimental Study for Site Preferences of Formability Improved Alloying Elements in Mg Crystal

Some alloying elements (Al, Er, Gd, Li, Mn, Sn, Y, Zn) were proved recently by calculations or experiments to improve the formability of Mg alloys, but ignoring their site preference in Mg crystals during the calculated process. A crystallographic model was built via first principle calculations to predict the site preferences of these elements. Regularities between doping elements and site preferences were summarized. Meanwhile, in the basis of the crystallographic model, a series of formulas were deduced combining the diffraction law. It predicted that a crystal plane with abnormal XRD peak intensity of the Mg-based solid solutions, compared to that of the pure Mg, prefers to possess solute atoms. Thus, three single-phase solid solution alloys were then prepared through an original In-situ Solution Treatment, and their XRD patterns were compared. Finally, the experiment further described the site preferences of these solute atoms in Mg crystal, verifying the calculation results.     

退火温度对HA/Ti-24Nb-4Zr复合材料组织与性能的影响

利用放电等离子烧结(SPS)技术制备了HA/Ti-24Nb-4Zr生物复合材料,研究了不同退火温度对复合材料显微组织和力学性能(抗压强度、屈服强度、屈强比、压缩弹性模量)的影响。结果表明,烧结态复合材料主要由β-Ti相、少量初生α-Ti相及HA相组成;随着退火温度的升高,复合材料基体中β-Ti相含量增多且晶粒逐渐长大,针状次生α-Ti相在晶界处和晶内不断析出,HA相结构和含量变化不大;与烧结态相比,不同退火温度处理后的复合材料强度和弹性模量先略微上升后下降,而塑韧性呈不断提高趋势;复合材料在850 ℃退火处理后,抗压强度、屈服强度、屈强比和压缩弹性模量值分别为1507 MPa、1270 MPa、0.84和42 GPa,塑韧性得到明显改善,作为生物医用植入材料具有潜在的应用前景。     

Kevlar织物软壁包容环抗冲击数值仿真分析研究

针对机匣包容性问题,提出Kevlar平纹织物本构模型的拟合方法,分别采用单层壳、多层壳、层合壳三种有限元建模方式对Kevlar织物软壁包容环弹道冲击过程进行模拟,发展了机匣包容性仿真分析模型。结果表明,多层壳模型和层合壳模型的计算结果更准确,并且可以通过调节摩擦因子使仿真结果与试验结果更接近。在此基础上研究了撞击点位置和弹体入射姿态对弹体剩余速度的影响。结果表明:在较小偏移距离内,撞击点的位置对剩余速度的影响可以忽略不计;滚转角和俯仰角对剩余速度影响较小,而对于偏航角,当角度大于30°时,剩余速度会随着角度的增大明显呈下降趋势,且弹体出射姿态也会发生明显变化。     

Analysis of color volume of multi‐chromatic displays using gamut rings

There are claims that multi‐chromatic displays can achieve a wider color gamut by the use of additional highly saturated secondary color channels. However, there are other claims that these displays lose lightness and/or color saturation at brighter levels. These apparently divergent views have led to some controversy in the display industry and at standard setting organizations. This study examines the color gamut volume for a variety of simulated and measured multi‐chromatic (sometimes incorrectly referred to as “multi‐primary”) displays using combinations of white and/or secondary color channels, such as cyan, magenta, and yellow. Furthermore, a two‐dimensional gamut representation, referred to as “gamut rings,” is introduced to illustrate that the addition of nonprimary optical color channels to a trichromatic (RGB) display can result in a significant decrease in the chroma at higher lightness levels. The additional saturated color channels can increase the gamut volume only around their hues at darker levels. The results also confirm the validity of comparing the color light output and white light output for revealing the design trade‐offs between the high‐peak white and the color‐image brightness for multi‐chromatic displays.     

Multimedia image quality assessment based on deep feature extraction

Multimedia Tools and Applications - Measurement of visual quality is of significant importance to many image processing tasks. The target of image quality assessment (IQA) is to design effective...     

Geometric calibration based on B-spline with multi-parameter and color correction based on transition template and decay function

Multimedia Tools and Applications - To achieve low-cost and fast multi-channel surface projection geometric correction, the quadratic quasi-uniform B-spline surface is used to reconstruct the...